Choose the finish before work starts, with the final paint and room lighting in mind.
A short guide to Levels 0–5
The six-level summary below is checked against the accessible GA-214-2021 reference. The publisher now lists GA-214-2026; its complete technical PDF has not been reviewed for this guide. Confirm the edition specified for your project and current product instructions before using this summary as a work specification.
Source: Gypsum Association; Gypsum Association
| Level | What the distinction means |
|---|---|
| 0 | No joint finishing. The final decorative treatment may not yet be selected. |
| 1 | Tape embedded at joints and interior angles; generally concealed areas. |
| 2 | Embedded tape with a thin compound covering; fasteners and accessories receive one coat. Used where the specified treatment does not prioritise appearance. |
| 3 | Additional joint treatment for specified medium/heavy textures—not a smooth painted finish. |
| 4 | Further joint and fastener treatment for specified flat-paint and other suitable finishes. |
| 5 | Level 4 treatment plus a skim coat across the entire surface; relevant to demanding paint and light conditions. |
Source: Gypsum Association
The Level 4 / Level 5 decision
CertainTeed explains how variations between board paper and treated joints can become more apparent under reflective paint or light travelling across the wall. A whole-surface skim coat helps provide a more uniform surface. This is why sheen and strong side lighting belong in the finishing conversation—not just in the paint conversation later.
Source: CertainTeed
- Show the contractor where large windows and wall-washing lights will be.
- Share the planned paint colour and sheen, even if they are provisional.
- Identify long, uninterrupted walls and ceilings that matter visually.
- Ask which surfaces the proposed finish covers, rather than applying a vague upgrade to the whole project.
Use a sample to agree the appearance
For a visually demanding room, ask the designer and contractor whether an agreed sample area would make the decision clearer. Record which wall it represents, the intended coating, the lighting and who accepts it.
A finish designation alone does not settle every appearance question. Put the final decorating scope and acceptance approach in the project documents so the drywaller and painter are working toward the same outcome.
Finishing and painting are separate scope decisions
| Ask about | What to write down |
|---|---|
| Joint finishing | The agreed level and exactly which surfaces it applies to. |
| Whole-surface work | Whether a skim coat is included and the boundaries of that work. |
| Primer & paint | The responsible trade, products and handover condition. |
| Review & touch-ups | When the surface is reviewed and how later damage is handled. |
Separate the suite assembly from its decorative finish
Surrey’s permit resources distinguish interior renovation, basement finishing and secondary-suite work. If your finish brief belongs to one of those projects, keep the approved wall or ceiling assembly with the drawings and specify the visible treatment separately. Choosing a smooth appearance is not evidence that the underlying permitted assembly has been restored.
Source: City of Surrey; City of Surrey
- Identify the surfaces and assembly details to remain consistent with the project drawings.
- Discuss colour, sheen and lighting only after the applicable construction scope is clear.
- Record who accepts the decorative sample and who confirms the separate construction checks.
A few practical questions.
Does every room need Level 5?
No. The decorative finish, light, surface and project requirements guide that choice. Discuss the room as it will actually be used and decorated; a higher number should answer a specific appearance requirement.
Is Level 5 the same as a perfectly flat wall?
No. A finishing designation describes treatment of the surface. It is not a promise that the underlying framing or completed surface is mathematically flat. Discuss the expected appearance and any underlying irregularities separately.
Sources & editorial context
- GA-214-2021 · Levels of Finish for Gypsum Panel Products (historical PDF reference)Gypsum Association · Checked October 24, 2026
- GA-214-2026 · Publisher catalogue (edition pointer; full PDF not reviewed)Gypsum Association · Checked October 24, 2026
- Details Matter: Specifying the Right Finish for the Right WallsCertainTeed · Checked October 24, 2026
- Residential Building PermitsCity of Surrey · Checked October 24, 2026
- Building InspectionsCity of Surrey · Checked October 24, 2026
Technical references support the points linked above. The checklists and planning questions are editorial guidance, not a specification or an account of a contractor’s completed work.
This guide has an open editorial check. Confirm the applicable reference edition and project-specific requirements with the responsible professional before work is agreed.